HT12E DATASHEET IN PDF

The capability to select a TE trigger on the HT12E or a DATA trigger on the HT12A further enhances the application flexibility of the 2 12 series of encoders. HT12E Datasheet, HT12E Holtek Encoder Datasheet, buy HT12E Encoder IC. The capa- bility to select a TE trigger on the HT12E or a. DATA trigger on the HT12A/B/C further en- hances the application flexibility of the 2.

Author: Arajas Mikataxe
Country: Libya
Language: English (Spanish)
Genre: Science
Published (Last): 3 May 2014
Pages: 254
PDF File Size: 9.70 Mb
ePub File Size: 18.68 Mb
ISBN: 726-3-88682-657-3
Downloads: 93706
Price: Free* [*Free Regsitration Required]
Uploader: Kigagrel

A basic connection diagram for the HT12E IC is shown below In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground. This data should be sent to the HT12D for decoding, it can either be sent directly through a wire or by using a wireless medium like RF or IR.

Interface GPS with Arduino. HT12E has a transmission enable pin which is active low. Choosing Motor For Robots.

Can range from 2. This cycle is repeated as long as TE is kept low.

These two ICs together form an Encoder and Decoder pair. These are the 8-bit address bits, which is used to protect your data.

Skip to main content. The 4-bit data that has to be sent has to be given to ht12 pins AD0 to AD1 and an address of 8-bit has to be set using the pins A0 to A7. So if you are working on a project which has to transmit a 4-bit data from one end to other either by wire or wireless then this IC pair will be best suited for you.

  BS 7448-1 PDF

Submitted by admin on 30 October Simply put, HT12E converts the parallel inputs into serial output. For decoding a data the IC will requires an oscillator, luckily this IC has one in-built. This pin has to be connected to Ground 0V to enable the Transmission. The IC has a built in oscillator.

HT12E Datasheet

Arduino based GPS receiver. TL — Programmable Reference Voltage. Pull the Transmission Enable pin pin 14 to ground to activate transmission.

SPI Module of Arduino. The primary function of HT12E is to encode a bit and send it out through the output pin. The IC is has a wide range of operating voltage from 2. Connected to the Ground of circuit.

This oscillator can be used by connecting these two pins through a 1M Resistor. In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground. Choosing Battery for Robots. Transmission enable; active low.

HT12E Encoder IC Pin Diagram, Uses, Equivalents & Datasheet

In this daasheet I have made all four data bits as zero lowwhen this is decoded we will get the same kind of bits on the output side of HT12D, similarly we can make any changes datasheeet these 4-bits and they will be reflected on the output side of the HT12D decoder IC.

They are paired with 2 12 series of decoders for use in remote control system applications. HT12E is an encoder integrated circuit of 2 12 series of encoders. They can also be connected to switches to manually send and receive data. This high-density System-in-Package SiP integrates controller, power switches, and support components.

  1746 - HSCE 2 PDF

It encodes the 12 bit parallel data into dataheet for transmission through an RF transmitter. These four pins are used to send data, the data encoded here will be decoded on HT12D IC sharing the same address bits.

As soon as TE returns to high, the encoder output completes its final hy12e and then stops. Virgin Galactic — Commercial Space Flight. You can know to set up the HT12D after this from here. The encoded bit can be obtained from the Dout pin pin It is mainly used in interfacing RF and infrared circuits. The Encoded 12 bit output data can be obtained from this pin. What is Web Browser.

HT12E Encoder IC

If you want security you can connect any of the 8 pins to 5V to make it high. Can be used in Home automation for short range remote switching Safety systems like Burglar alarm system, Smoke or Fire alarm system etc. These 12 bits are divided into 8 address bits and 4 data bits. We should set the bits in same pattern on Encoder and Decoder IC to pair them. It is very important that your Decoder should also have this same address for them to talk to each other.

HT12E begins a 4-word transmission cycle upon receipt of a transmission enable.