The Uniden Bearcat BCT15X is the follow-up to Uniden’s premier analog mobile scanner, the manual for the radio is contained on a CD-ROM, in PDF format. DImage_/Manual/ (1 of 3)5/26/ .. This page applies to the following scanner(s): BCDXT BCT15X UnidenĀ® and BearcatĀ® are registered trademarks of Uniden America Corporation. View and Download Uniden BCT15 owner’s manual online. scanner radio with You can adjust the level of the following tones: Key Beep, BearTracker Alert.

Author: Mocage Tozuru
Country: Mongolia
Language: English (Spanish)
Genre: Photos
Published (Last): 25 August 2009
Pages: 306
PDF File Size: 19.68 Mb
ePub File Size: 4.69 Mb
ISBN: 701-6-99332-501-6
Downloads: 93291
Price: Free* [*Free Regsitration Required]
Uploader: Kakazahn

A will appear in the display. Select ‘ All Range ‘ to be alerted regardless of your direction of approach. However, if you believe your BCT15 is not performing properly, try these suggestions.

This means that you may hear transmissions from a distant system when your local system is not transmitting. To toggle Group Quick Keys on or off while scanning the systemquickly press then press the number key assigned to the group. Broadcast screen is not effective during some service searches. Set the dimmer to Auto if you are going to hard-wire your scanner inside your vehicle.

Set Type If you want to change the location type, the scanner resets the available options based on the new location type and the scanner goes back to the ‘ Program Location ‘ bearcwt for that location.

Top Questions for Uniden BCT15X Scanner

You can also toggle attenuation for weather scan by pressing then 7 Att. These limits are designed to provide reasonable protection against harmful interference in a residential installation. Never connect any part of the headphone jack to the antenna jack or connect the radio to an bct155x where the antenna and audio connection are bct15d.


Priority ID Scan This function is similar to conventional priority although there is no interruption during the transmission.

Uniden BCT15X Scanner

No] The scanner replaces the third line on the display with trunking activity indicators. The scanner deletes the frequencies in this system when you turn the power off.

After scanning your programmed systems, the scanner will scan the enabled state-by-state agencies, then resume scanning your programmed systems. Press to hold on a channel, frequency, search, Close Call hit, or Bearat search.

You need tone-out setup information from the agency you wish to monitor. Set C-CH Output allows you to choose how you want the scanner to handle control channel data output. Once you have your Systems built, systems options configured, Sites Created for trunking systemsSite Options configured, and Groups Createdyou can finally program your channels. The items below do not follow the radio’s menu order because IMHO they should be in the following order to properly setup and use the weather operation features.

Setting Up Your Scanner These guidelines will help you install and set up your new scanner: Broadcast Screen – allows the scanner to ignore hits on known broadcast frequencies including pager frequencies in search and Close Call modes.

There is no ‘per channel’ delay; you must set the delay for the whole system all sites, all groups, all channels. For more information about Uniden and our products, visit http: This will give you ‘ Nothing to Scan ‘ in the display. It does not scan them; Tone-Out monitors the frequency for all Tone-Out channels with the same frequency. The currently-selected menu item is highlighted with a bar on the display. Please review those first. Preemptive Priority – a feature that works on Motorola systems.

This is a system that automatically stores the frequencies found by Close Call. To program the current location press and hold GPS for 2 seconds. The band number will blink under the band that the hit was found in. Startup Configuration can’t be canceled once you start using it; the scanner remembers the last use configuration unless you use another, still scans multiple trunking systems relatively slow even with the hold time set to 0 especially if you have a lot of IDs programmed.


Conventional systems operate similarly, but all unlocked channels are scanned at least one time regardless of the hold time setting. In Close Call Only Mode: Set Delay Time this setting determines how long the scanner waits after a transmission ends before resuming Quick Search and Close Call Search operations. While Scanning or Searching with Close Call Override set to Offwhen the scanner detects a Close Call signal, the scanner does not override the current audio.

To overwrite and store the current location press and hold GPS for 2 seconds. To move the marker one frequency step turn. Quick Search – lets you search from the currently-tuned frequency or channel or enter a frequency and start searching.

In this case, the scanner displays each Tone-Out channel for two seconds.

Scanner Enthusiast Welcome to the family of Uniden scanner users. Other than the antenna, you have no control over these factors, but they explain why performance might vary by both location and bearrcat. To toggle Alert Mute on or off temporary: Up to systems, 1, total sites max per system20 groups per system, and 25, channels max IDs or 1, frequencies per system.