ASTM F146 PDF

F – 80 Standard Test Methods for Fluid Resistance Of Gasket Materials. Designation: F – Standard Test Methods for. Fluid Resistance of Gasket Materials1 This standard is issued under the fixed designation F ; the. ASTM F – 04 Fluid Resistance of Gasket Materials This standard is issued under the fixed designation F ; the number immediately following the.

Author: Taugrel Virr
Country: Namibia
Language: English (Spanish)
Genre: Medical
Published (Last): 6 May 2009
Pages: 412
PDF File Size: 9.89 Mb
ePub File Size: 17.65 Mb
ISBN: 504-8-34924-445-7
Downloads: 90099
Price: Free* [*Free Regsitration Required]
Uploader: Gagis

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

After immersing the specimens in the various test fluids, the effect on physical properties is expressed as change in ff146 strength, compressibility in softened condition, flexibility, volume change, and thickness and weight changes from the original condition.

The change in weight of the specimens is to be calculated as an expression of percentage change on the original weight.

We are a non-profit group that run this website to share documents. We need your help to maintenance this website.

There were six Type 1,7, three Type 3, and one Type 5 material evaluated for immersion weight change and thickness change in IRM oil. Precision and Bias 7 These test methods are not applicable to the testing of vulcanized rubber, a procedure that is described in Test Method D These test methods are applicable to ethylene glycol, propylene glycol, commercial coolants and blends with water thereof see Note 1water, and other commercial oils and fuels.

  DA PAM 600-26 PDF

ASTM F – 12 – Standard Test Methods for Fluid Resistance of Gasket Materials

Originally approved in These test methods are not applicable to the c146 of vulcanized rubber, a procedure that is described in Test Method D It is designed for testing specimens cut from gasketing materials or from finished articles of commerce.

Refer to Test Method D asstm further information regarding immersion test fluids. It is designed for testing specimens cut from gasketing materials or from finished articles of commerce. A number in parentheses indicates the year of last reapproval.

ASTM F146 – 12

Measure the weight of the test specimen to the nearest 1 asstm 0. BoxTrenton, NJ A superscript epsilon e indicates an editorial change since the last revision or reapproval. The change in thickness of the specimens is to be calculated as an expression of percentage change from the original thickness. Last previous edition approved in as F — The results of these test methods are not intended to give any direct correlation with service conditions in view of the wide variations in temperature and special uses encountered in gasket applications.

ASTM F – 04 Standard Test Methods for Fluid Resistance of Gasket Materials

ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. Historical Version s – view previous versions of standard.

It is the d146 of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Pour enough fresh test fluid over the specimens to ensure that the specimens are wetted and covered by the fluid.

  JVC GY-DV500 MANUAL PDF

ASTM F 146 – 04

If such information is not available, then the material should be tested by itself in fresh fluid to determine compatibility with said fluid. The producer must be aware that different coolant mixtures may yield different results.

This gives the final volume, V2. Size px x x x x Dead weight loads are listed in Table 1. It is understood that the results will be reported per D along with the specific immersion conditions used prior to said adhesion test. Use enough fluid to provide a minimum of 10 mL for each specimen in the container. The user should be aware that results may differ.

Please fill this form, we will try to respond as soon as possible. Type 1 Class 2—A BA material, containing a normally lower swelling ast. Current edition approved April 1, Insert the aluminum-foil covered stoppers into the test tubes before placing them in the supporting rack within the oven.

ICS Number Code Please copy and paste this embed script to where you want to embed Embed Script.