ASTM D413 PDF

ASTM D determines the adhesion strength required to separate a rubber layer from a flexible substrate such as a fabric, fiber, or sheet metal. Our universal . This part of ASTM D specifies the test conditions for determining the adhesion strength between piles of fabric bonded with rubber or the adhesion of the. GeoTesting Express is a provider of Geosynthetic Testing Services – ASTM D, Standard Test Methods for Rubber Property-Adhesion to Flexible Substrate.

Author: Kagore Goltizuru
Country: Singapore
Language: English (Spanish)
Genre: Sex
Published (Last): 23 June 2007
Pages: 410
PDF File Size: 8.32 Mb
ePub File Size: 12.60 Mb
ISBN: 999-7-71849-807-6
Downloads: 43656
Price: Free* [*Free Regsitration Required]
Uploader: Doukasa

G Series Mechanical Vice Grip. In an adhesion test, a layer is stripped off a test specimen using an applied tensile force – this results in tearing at the bonded surfaces. For Type A, you must perform a degree peel. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

ASTM D413 Rubber Property – Adhesion to Flexible Substrate

Users of previous versions of software such as Bluehill 2 and Bluehill 3 can easily upgrade to the newest version of Bluehill. The standard defines three types of specimens: The acceptable value of adhesion measured will, of course, vary from product to product due to different rubber d41, flexible substrates, and types of products.

With the mandrel attached to the recording head of the d4133 and the separated layer gripped symmetrically and firmly without twisting in the power-actuated clamp, and start the machine.

We are confident that we have what you are looking for. Subscribe to Our Newsletters. Type B requires a 90 degree peel. Software for Series Systems. Astmm the specimen snugly on the test mandrel. In peel tests, the data acquisition rate is critical for repeatable and accurate results. Line contact and special coated faces are also available.

High, uniform data acquisition rates d4133 with a proper bandwidth provide the best results. Email addresses can only contain letters, numbers and the following special characters: Bluehill LE for Basic Testing. Provide for maintaining the strip during the test approximately d41 the plane of the clamps.

  AELRED SPIRITUAL FRIENDSHIP PDF

Separate by hand a sufficient length of a layer of the specimen to be tested to permit the power actuated clamp of the machine to be attached.

With our test machine, the rate of separation is fixed and the adhesion value is expressed in terms of the measured force. By continuing to use our site, you accept our cookie policy. Separate the parts to be tested by hand at one end of the test specimen and at a sufficient distance to permit grips of the machine to be attached. Concrete, Asphalt and Rock. Onsite Training At Your Asttm. Next Checking to see if you are a returning visitor…. Strip the separating layer from the specimen at an angle of approximately 90 degree to the tangent of the specimen surface, and continue the separation for a sufficient distance to indicate the adhesion value.

However, once a product is established, minimum values of separation force can be determined and agreed to by producer and consumer and both can monitor to assure maintenance of the agreed-upon minimum value. They can be equipped with a selection of c413 grip jaw faces in various sizes and choice of surfaces including smooth ground, rubber-coated and serrated.

Separate by hand a sufficient distance along astk separation line in the center of the strip to permit the grips of the machine to be attached.

Active Risk Management

Link to Active This link will always route to the current Active version of the standard. How can we help you? Bluehill Universal Brochure Bluehill Universal Software is built from the ground-up for touch interaction and an intuitive user experience.

Adhesion is expressed as the average force required to astj separation at a definite rate, or the average rate of separation caused by a known or specified force. Discover simpler and smarter testing with features such as pre-loaded test methods, QuickTest in seconds, enhanced data exporting: Peel along the previously cut separation layer for 40 to mm. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

  HITACHI CPX8160 PDF

Forces up to 10 kN 2, lbf Low force tabletop systems Modular series of five frame options with adjustable test space Affordable testing option ashm tension, compression, bend, peel and much more.

ASTM D – 98() Standard Test Methods for Rubber Property—Adhesion to Flexible Substrate

We offer machines, apparatus, testers, asgm grips, test fixtures, clamps, holders, jigs, ashm, jaws, extensometers, environmental and humidity chambers, furnaces, baths and custom solutions for unique applications. Instron’s Bluehill application software’s Peel, Tear, Friction module captures these results and reports them automatically, as well as displaying them on graphs and tables.

Subscribe to Instron News! Attach the separated end of the specimen, with all separate parts except the one under test securely gripped, to the recording head by means of a grip. WaveMatrix 2 for Dynamic Testing. Type C is for ring specimens. Have a question about conducting the test for this standard?

Our universal testing machines can be used to perform the method described in this standard. Rated to N 50 lbf Maximum specimen thickness of 8 mm 0. How can we help you? The test involves taking a strip of material with both layers bonded together, initiating an artificial “tear”, or separation at one end of the strip, inserting these free ends into a set of grips, and pulling the layers apart.